ZHEJIANG XINCHOR TECHNOLOGY CO., LTD.
XINCHOR TECHNOLOGY CO., LTD. Manufacturer of Structural Strengthening Products Since 2000.
Add to Cart
1000ml 1:1 Cartrige Epoxy Chemcial Anchor Adhesive For Structural Strengthening
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing glue,
Chemical anchoring system used for anchoring and rebar connections in concrete.
Item #: FixingChor110
Capacity: 1000ml
Materials: Epoxy
Mixing Ratio: 3:1
Product Description:
1000ml 1:1 Cartrige Epoxy Chemcial Anchor Adhesive For Structural Strengthening is
a two component, high tensile strength, modified pure epoxy chemcial anchor adhesive.chemical fixing system
strong fixing with exceptionally high chemcial resistance.Applied in one single action this resin will produce a high performance,
Suitable for
Non-cracked concrete
Reinforcement bars
For fixing of:
Steel constructions
Consoles
High-racks
Machines
Staircases
Wooden constructions
Reinforcement bars
Pass GB50728-2011
Humidity resistance testing
Freeze-thaw resistance Testing
Resistance to fatigue stress Testing
Resistance of long term stress testing etc .
Can be used in projects with Design Period of 50 years.
| Testing Items | Condition | Index | ||
| Adhesive Performance (According to China National Standard GB50728-2011) | ||||
| Splitting Tensile Strength (MPa) | Under (23±2)℃,(50±5)%RH, tested by loading speed of 2mm/min | ≥8.5 | ||
| Flexural Strength (MPa) | ≥50 (no fragment damage) | |||
| Compressive Strength (MPa) | ≥60 | |||
| Bonding Capacity (According to China National Standard GB50728-2011) | ||||
| Steel-Steel Tensile Shear Strength (MPa) | (23±2)℃,(50±5)%RH | ≥10 | ||
| Bonding strength of Ribbed steel bar (or screw) with concrete under constrain drawing condition | (23±2)℃ (50±5)%RH | C30,Ф25,L=150mm | ≥11 | |
| C60,Ф25,L=150mm | ≥17 | |||
| Steel-Steel T-peeling strength (mm) | (23±2)℃,(50±5)%RH | ≤25 | ||
| Non-volatile content | (105±2)℃,(180±5)min | ≥99% | ||
| Ageing resistance to heat and humidity 90d | ||||
| Reduction rate of tensile strength | Under normal room temperature | ≤12% | ||
| (According to China National Standard JGJ145-2013) | ||||
| Tensile Strength (after high temperature welding) | Dia12 Grade II steel, C30 concrete Hole dia.16mm, Depth: 150mm | 55.1N, 57.0N, 54.8N | ||
Approved for anchorings in
Railway or express way modification works
Structure reinforcement
Curtain wall installing
Concrete, cracked and non-cracked Applications
Rebar planting in concrete structures.
Bridge modification works
Keel fixing in out wall
ATTENTION
- Do not install anchors when the temperature is less than 10°C.
- If the cartridge is not finished, please clean the opening, then put the plug back and cap tightly.
- At temperatures below 10°C should be warmed or stored in temperatures
of 10-30°C for 24hours prior to use to improve product flow and cure.
- If the gelling time expires, please use a new static mixer.
- Do not cut or shorten nozzles.
- It can be used again in the future by replacing the static mixer.
- Please ensure hole is properly cleaned. Hole may be damp but must be free from water.
- Do not install anchors when substrate temperature is less than 0°C.
